奥的斯ACD系列通用最新故障码(下)

湘军

使用服务器M1-1-2-1查看到的所有故障记录，所有事件类别分为I/W/F/E

I	Information	信息
W	Waring	警告
F	Fault	错误
E		Elite - Visible only in the ALL Menu Event Trace

savedRuns	从上次送电到现在的运行次数
savedMins	从上次送电到现在的时间（单位：分钟）

故障代码

故障名称

类别

故障解释

相关设置

System
0600	SPB-Alert	W	服务面板检测到一个错误，需要手动救援SPB 和 SDI。可能的原因有:SDI 的错误的速度编码器 SPB 上缺陷的 E2PROM SPB 上的电池缺失 按SPB 按钮，REB+DDO 同时，以定位错误源 控制板检测到 SPB 和 SDI 故障. Ssk 可能的原因有： 1.编码器故障 2.SPB 上的 E2 存储器故障 3.电池故障 同时按 SPB 上的 REB+DDO 定位故障原因 Error # 1, encoder A failure (only ...AAA/...AAB) Error # 2, encoder B failure (only ...AAA/...AAB) Error # 4, E2Prom failure Error # 5, battery failure Error # 12, 3 encoder A failure Error # 13, received out of range parameters from TCBC/GECB /RCBII
0601	SPB:TempHTS	W	服务面板过热。	SPB-Temp
0602	LwssService	W	称重板请求REM。参见称重板故障原因。称重系统请求服务
0603	Aro Service	W	The ARO subsystem (modified SPBC_III) requested “Request For Service” (REM). See ARO subsystem’s event logging for reason.
0604	S/WChanged	I	软件变更。SCN 更改
0605	Update S/W!	F	升级软件！要求更新 GECB 软件
0606	SpbService	W	SPB 请求服务
0607	/TUM1	F	TUM1 missing after run at TOP or active during standstill; (reduced overhead: trig- ger modulcontacts)	TUM1(1047) HWY-TYP
0608	/TUM2	F	TUM2 missing after run at TOP or active during standstill; (reduced overhead: trig- ger modulcontacts)	TUM2(1048) HWY-TYP
0609	/TDM	F	TDM missing after run at BOTTOM or active during standstill; (shallow pit: trig- ger modul contacts)	TDM(1049) HWY-TYP
0610	/TUPS	F	TUPS missing during run; (reduced overhead: trigger modul power supply)	TUPS(1050) HWY-TYP

0611	/TDPS	F	TDPS missing during run; (shallow pit: trigger modul power supply)	TDPS(1051) HWY-TYP
0612	SOS up	F	Safety Operated Switch Up triggered	SOSU(1054) HWY-TYP
0613	SOS down	F	Safety Operated Switch Down triggered	SOSD(1055) HWY-TYP
0614	PRBB BatLow	W	The battery of the PRBB board is weak: During PowerOff, the battery only pro- vides power for less than 10 seconds.	EN-PRBB=1
0615	PCB Certi	W	The PCB certification is not performed by using OEK PDA until the specified days expired. In order that this function is ap- plied, it should be set by OEK PDA. Note: only for Korea application
0616	C-circuit	F	C-circuit does not work correctly Note: only for MCS310	C-CHK (704)
0617	RBU-Selftst	F	Selftest of Rope Brake has failed (i.e. lasted longer than 5 seconds). Car is blocked until TCI/ERO is switched.	RBTC (1029) RBTE (1028)
0618	RBU-Fault	F	Rope Brake has detected overspeed. Car is blocked until TCI/ERO is switched.	RBTC (1029) RBTE (1028)
0619	HWY-TYP	F	Please refer to blinking message “LOPIT cfg!”	Low Pit
0626	DeepBattery	F	LVA Switch or Evolux: Deep Discharge Protection switched off the OCB to pro- tect the batteries (voltage was < 40 VDC).	GECB-LV DRV-TYP
0627	LowBat wait	F	LVA Switch or Evolux: Enforced Battery Charging	GECB_LV DRV-TYP
0628	NoPowerWait	F	LVA Switch or Evolux: BatRun-T expired during blackout	GECB-LV DRV- TYP BatRun-T
0629	HighBatWait	F	LVA Switch: Enforced Battery Discharg- ing Battery voltage exceeded 70 VAC.	GECB-LV
0630	OverBat	F	LVA Switch: Overvoltage Protection is going to switch off the OCB to protect the batteries (voltage > 75 VDC).	GECB-LV
0631	E2P Mapped	I	The LCB2/TCBC E2Prom data, provided by an E2TB (E2prom Transfer Board) were mapped to the GECB layout
event
0701	SP missing	F	Node Guarding does not detect the SP at the CAN bus. Check CAN_OK LED at SP; Check CAN wiring between GECB & SP;
0702	BCB missing	F	Node Guarding does not detect the 1st BCB at the CAN bus. Check CAN_OK LED at LVPB/BCB_II Check CAN wiring between GECB & LVPB/BCB_II
0703	BcbIoFail	F	The state of inputs was not received eve- ry second or the output command was not acknowledged. CAN bus overload? Defect LVPB/BCB_II?
0704	BcbHwFail	F	The BCB published an EEPROM error. Exchange LVPB/BCB_II
0705	BcbSwFail	F	The BCB published a task timing prob- lem. See subcode ‘x’ for details Exchange LVPB/BCB_II according to subcode
0706	EncoderFail	F	The rescue encoder generates no signals during a normal run. Check rescue encoder wiring; Replace rescue encoder or GECB_II;
0707	OCB fail	F	The OCB auxiliary contacts are wired incorrectly. Check wiring to OCB; Check OCB; Check GECB_II inputs;
0708	Overspeed	W	The measured rescue encoder speed is 15% faster than the nominal speed. The OS contact or the safeties could be acti- vated. MRO is prevented. Reset OS contact; Check Encoder / Speed parameter;	SPEED Encoder
0709	MRO_BRK Flt	F	A wrong voltage at the brake was detect- ed. That means that the brake could be unin- tentionally lifted during MRO. Check input MRO_BRK and wiring of the brake Check LVPB / Replace LVPB DO NOT PERFORM MRO!!!	LVA
0710	No Battery	F	The 1st BCB misses the rescue battery. Check RPS / battery
0711	BatTempErr	W	The 1st BCB indicates that the battery cannot be charged, because the tempera- ture is out of range. Check battery temperature sensor

注:删除单个故障：服务器 GO ON 或者 GO BACK 选中将要删除的故障

SHIFT(蓝健) + 1 (ON) 然后 SHFIT + CLEAR (ENTER) 当前单个故障删除

新版本有 M1-1-2-7菜单,代替了SHIFT（蓝健）+UP（2 ）

了解详细的清除主板故障步骤在公众号里找:奥的斯服务器查看主板故障清除故障